I get following error message while building Yocto Image - imx-image-full  Looks like this repository is not public.  ERROR: nxp-wlan-sdk-git-r0 do_fetch: Fetcher failure: Fetch command...

Dear @Anooj Gopi, We are currently working on the Android BSP source for IMX8MP. Hopefully, it will be done by the end of next week. Once it's done, we'll get back to you. We apologize for any inco...

Hello,  I'have  build yocto boot part as described in the docs and i added an Ubuntu rootfs .  have copied  modules folder from modules--5.4-r0-lec-imx8mp-20221026135341.tgz i...

Dear Support Team, From where can I download the Android BSP source code for I-Pi SMARC IMX8M Plus? We have to do customization for the PoC for which we need access to the Android BSP (Kernel/HAL/...

Dear @O. JUD, It is possible to fix the mac address. Please follow the below steps, Boot into U-BOOT (emmc boot) and type the following commands,            =>...

Dear @O. JUD, Please refer to the following page (https://www.ipi.wiki/pages/downloads-imx8mplus). Please download the schematic file of IMX8MP and see the page number-17 for more details.

Dear @Laurent Rouvet, we will add them in the future.

Could you add the connector reference into the documentation?

Hi ,  Is there a way to fix the mac address on EVK board I-Pi SMARC Plus IMX8M ?  I'm using Yocto a build image from adlink-lec-imx8mp-yocto-hardknott_1v2.xml  I read about efuse ...

Hi Could you provide the reference of the connector for the audio expension card on the carrier board ?      Regards

Hi  Regarding the chapter bellow in SMARC 2.1 Specification i think it can be managed.  i'm wondering if it's related to power regulator framework as described in chapter 2.5.2.5 Regula...

Dear @Shawn Doherty, It is possible to power on the targeted device by following the below link. https://www.ipi.wiki/pages/comhpc-docs?page=HowToConfigureBMCMACIPAddress.html 

Dear @O. JUD, USBX_EN_OC indicates "Over Current Protection" for the board. Furthermore, its states cannot be managed.

Is it possible to enable Power On after Power Loss from BIOS?   Version: TianoCore 2.04.100.06.A1 (SYS:.2.06.20220308)

Hi,  I'm wondering what is ports like USB0_EN_OC,USB1_EN_OC,USB2_EN_OC ...  shown in your datasheet (Page 4).  I understand is for power on/off usb port . am i right ?  If ye...

@Jared Jensen NXP didn't support the native Ubuntu image. Acually,   this instruction is using Ubuntu rootfs which is on the top of NXP kernel image and the building logic should work on...

I plan to purchase the I-Pi SMARC IMX8M Plus development kit to get started.  However at some point I would like to try a SMARC module using the i.mx8 QuadMax with 4 Cortex A53 and 2 Cortex A7...

Dear @Dennis Gilmore, Our recommendation is to use: 32GB DDR4 RDIMM 3200 VLP Transcend, TS4GHR72V2EL (29-6AE00-7430) There are also other memories that have been tested and can be used, such as:...

Maybe I have missed I somewhere, I would like to bump the memory to 128GiB, I am trying to figure out what ram modules are compatible so I can get there. I currently have 4x16GiB and would like to ...

Dear @Todd Bonack,      The PX30 supports OTG Mode, and by default the g_serial gadget is loaded, so you need to remove it to load ether. Here are the steps to follow to make PX30 w...