Dear @O. JUD, iMX8MP UBoot is configured to use the default ENV_SIZE and ENV_OFFSET specified by NXP. CONFIG_ENV_SIZE=0x4000 CONFIG_ENV_OFFSET=0x400000 We were able to read out the ...
Dear @O. JUD, iMX8MP UBoot is configured to use the default ENV_SIZE and ENV_OFFSET specified by NXP. CONFIG_ENV_SIZE=0x4000 CONFIG_ENV_OFFSET=0x400000 We were able to read out the ...
Dear @Gonzalo Samper, Yes. It is fully supported by our I-Pi SMARC RB5 Dev Kit.
Dear @Kieran Thompson, It is not advisable from our side, the recommended voltage always must be 9V - 19V.
Dear @Jackie Lee, It was a documentation error. We will update it ASAP. Please use the Linux(Ubuntu) host system to flash the image. ## Flashing Android Image 1. Copy the prebuilt bootable...
Dear @Neha Gupta, Depending on how much load the Ubuntu desktop image has, the processor might slow down. The reason why the eMMC can't be detected as a storage device on your host device is that...
Dear @O. JUD, Module MAC addresses are not set by us. It is by default that the MAC address will change randomly, but if you would like a fixed MAC address, you can do so.
Dear @T. I. , If the image is not flashed successfully this kind of issue may happen. Please try to flash the image again as mentioned here Change the boot option as shown here If still it doe...
Dear @Laurent Rouvet, The device tree "lec-imx8mp-hydis-hv150ux2.dts" is only compatible with HYDIS HV150UX2-100 18 dual panels LVDS Display. Obviously, it won't work if you are using another type ...
Dear @O. JUD, You can either use LVDS or HDMI. Both can't be used simultaneously. You don't need to change the dtb for HYDIS screen. For more details, you can refer NXP website.
Dear @Jared Horton, Your SSD is a SATA type, so please use an NVMe type SSD. Our IMX8MP does not support SATA type SSDs. In addition, we have used the latest Ubuntu image for validation. The file c...
Dear @O. JUD, By default, our image can support the following LVDS panel(HYDIS HV150UX2-100 18 dual panels). Don't need to change anything in the dtb. we recommend the following steps to set up the...
Dear @Jared Horton, we found the problem. This was caused by a compatibility issue with the IMX8M Plus board. It is necessary to use an SSD type that supports NVMe SSD M.2 B key. As part of our val...
Hi @O. JUD, our image won't support this future. For more details, you can refer to the NXP official website.
Dear @O. JUD, Please use the following command while building the image. repo init -u https://github.com/ADLINK/adlink-manifest -b lec-imx-yocto-hardknott -m adlink-lec-imx8mp-yocto-hardknott_1v5.xml
Dear @Mark Abrams, I apologize for the inconvenience. The mail had been sent to the wrong address. The mail has been forwarded to you just now. The subject of the mail is "FW: [I-Pi SMARC's Forum] ...
Dear @Jared Horton, Our I-Pi SMARC IMX8M Plus board doesn't have the BIOS settings.
Dear @O. JUD, Here is the link for building the Yocto image for our I-Pi SMARC IMX8M Plus product, it has all the packages and drivers you need. https://www.ipi.wiki/pages/imx8mp-docs?page=HowToBu...
Dear @Sven Brandau, Sorry for the inconvenience. A kernel upgrades from Zeus to Kirkstone is currently underway. Additionally, it is a time-consuming process. The software will be available for all...
Dear @Jared Horton, Our apologies for the inconvenience. In our case, we also encountered the same issue. This issue has been reported to our software team, so please wait for our update.